Помогите с распайкой
Имеется Макентошевский PowerPC G3. К нему нет родного моника и адаптера для обычного моника, соотвецтвенно, тоже. Попытался спаять сначала по этой распайке http://www.hardwarebook.info/Macintosh_Video_to_VGA потом по этой http://www.hardwarebook.info/Macintosh_Video_to_VGA ничего не вышло. Если есть у кого-то опыт, прошу поделиться. На форуме вроде эта тема не обсуждалась.
Macintosh Video to VGA (Помогите с распайкой)
Во, такая же беда, спаял переходник по pinouts:
http://pinouts.ru/VideoCables/MacVideoToVGA.shtml
Подключаю к "Macintosh Quadra 605" Монитор пытается стартонуть и отрубается,
где и куда перемкнуть не понял (по английски шибко плохо понимаю):
Notes:
1) Sense pins 4, 7, and 10 are referred to as MON.ID1, MON.ID2, and MON.ID3 in the Macintosh pinout table or SENSE0, SENSE1, and SENSE2 in pinout tables for the video connectors. A sense pin value of 0 means that pin should be grounded to the C&VSYNC.GND signal (pin 11); a value of 1 means do not connect the pin.
2) Extended sense codes will be examined if the following sense code is detected: 1 1 1 (no sense pins grounded).
NOTE for extended sense codes: Sense pin pair value of 0 means those pins should be tied together (as opposed to grounding 10, 7, or 4 to pin 11); value of 1 means leave open. DON"T wire any of these pins to ground.
Типа искомое (VGA 640 x 480) 10-7 (0) типа замкнуть контакты? На схеме замкнуты через диод,
какой? (марка, мощность) от обычного нет результата.
У кого есть опыт?
http://pinouts.ru/VideoCables/MacVideoToVGA.shtml
Подключаю к "Macintosh Quadra 605" Монитор пытается стартонуть и отрубается,
где и куда перемкнуть не понял (по английски шибко плохо понимаю):
Notes:
1) Sense pins 4, 7, and 10 are referred to as MON.ID1, MON.ID2, and MON.ID3 in the Macintosh pinout table or SENSE0, SENSE1, and SENSE2 in pinout tables for the video connectors. A sense pin value of 0 means that pin should be grounded to the C&VSYNC.GND signal (pin 11); a value of 1 means do not connect the pin.
2) Extended sense codes will be examined if the following sense code is detected: 1 1 1 (no sense pins grounded).
NOTE for extended sense codes: Sense pin pair value of 0 means those pins should be tied together (as opposed to grounding 10, 7, or 4 to pin 11); value of 1 means leave open. DON"T wire any of these pins to ground.
Типа искомое (VGA 640 x 480) 10-7 (0) типа замкнуть контакты? На схеме замкнуты через диод,
какой? (марка, мощность) от обычного нет результата.
У кого есть опыт?
http://www.phantom.sannata.ru/forum/index.php?t=11884
Сортирую запасы, лишнее при нахождении буду размещать на форуме.
Сортирую запасы, лишнее при нахождении буду размещать на форуме.